🥝GuideKiwi
Free Guide

Your Free Guide to Replacing a Whirlpool Refrigerator Water Filter

Understanding Whirlpool Refrigerator Water Filters and When to Replace Them Whirlpool refrigerators use water filters to remove contaminants from water and i...

GuideKiwi Editorial Team·

Understanding Whirlpool Refrigerator Water Filters and When to Replace Them

Whirlpool refrigerators use water filters to remove contaminants from water and ice that your family consumes. These filters contain activated carbon and other materials designed to reduce chlorine taste and odor, sediment, and some other impurities. Over time, the filter becomes saturated with the particles it has captured, and its ability to clean water decreases significantly.

Most Whirlpool refrigerators require filter replacement every six months under normal use conditions. Some households with heavily chlorinated water or higher water usage may need to replace filters more frequently—every three to four months. Conversely, households with lower water usage might extend replacement to eight or nine months. The actual timeframe depends on your local water quality and how much water and ice you dispense from your refrigerator.

Your Whirlpool refrigerator likely has a filter status indicator light on the control panel. This light typically shows green when the filter is functioning properly and changes to yellow or red when replacement is approaching or overdue. Some models display the remaining filter life as a percentage. Ignoring this indicator means water quality gradually decreases, and the filter may eventually stop working altogether, potentially allowing unfiltered water into your system.

Different Whirlpool models use different filter cartridges. The most common types include the 4396508 filter (used in many French door and side-by-side models), the 4396710 filter, and the 4396841 filter. Checking your refrigerator's model number—found on a sticker inside the fridge or on the back—will tell you exactly which filter your unit needs. Using the wrong filter type won't fit properly and won't provide appropriate filtration.

Practical Takeaway: Locate your refrigerator's model number and filter type now, note when you last replaced the filter, and monitor your filter status light regularly. Setting a phone reminder for the six-month mark helps you plan ahead rather than discovering a clogged filter unexpectedly.

Tools and Materials You'll Need for Filter Replacement

Replacing a Whirlpool refrigerator water filter requires minimal tools and materials, making this a project most homeowners can complete in under ten minutes. Having everything prepared before you begin prevents interruptions and reduces the time your refrigerator sits open during the process.

The primary item you need is the replacement filter cartridge itself. Purchase the correct model number from retailers like Amazon, Walmart, Best Buy, Home Depot, or directly from Whirlpool's parts website. Prices typically range from $25 to $60 depending on the filter type and retailer. Some people buy filters in bulk (packs of two or three) to save money, which makes sense if you own your home and plan to stay several years. You should have the new filter on hand before your current filter needs replacement.

Beyond the filter cartridge, you'll need a small bucket or container that can hold at least two to three quarts of water. This catches water that remains in the filter housing and tubing after you shut off the system. A clean kitchen towel or paper towels help absorb spills and dry any water from the refrigerator's exterior. Some people wear an apron to protect their clothing, though this isn't necessary.

Depending on your Whirlpool model, you may need a flathead screwdriver or coin (like a quarter) to turn the filter housing clockwise or counterclockwise. Many newer Whirlpool filters use a simple hand-turn design that requires no tools at all. Check your refrigerator's manual or the filter packaging to see if tools are needed. Having a stepladder nearby helps if your filter is located in an upper cabinet or difficult-to-reach location.

Some people find it helpful to have a damp cloth available to wipe down the filter housing area before installing a new filter, particularly if dust or debris has accumulated. This takes only an extra minute but ensures the new filter sits in a clean environment and reduces the chance of particles entering your water system during installation.

Practical Takeaway: Gather your replacement filter, bucket, towels, and any needed tools in one location before starting. Review your refrigerator manual or watch a 2–3 minute video specific to your model number to see the exact filter location and removal method.

Locating Your Water Filter and Preparing for Replacement

Whirlpool places water filters in different locations depending on the refrigerator model and design. The most common location is inside the refrigerator itself, usually in the upper right corner behind a small panel or in the base grille at the bottom front of the unit. Some models mount the filter inside a cabinet above the refrigerator or in a separate housing beneath the sink (though Whirlpool's built-in and countertop filters are more common in refrigerators). Knowing your exact location prevents wasted time searching.

Open your refrigerator and look for a small cylindrical cartridge or a round plastic housing with a cap. The housing typically has a blue, white, or black plastic exterior. If you see nothing obvious in the upper sections, check the base grille at the bottom front of the refrigerator—you may need to remove a small panel or unscrew a cover to access it. Your refrigerator's manual includes a diagram showing the exact filter location, and this information is often printed on the inside of the refrigerator door or on the main control panel.

Before touching anything, turn off the refrigerator's water supply. Most refrigerators have a small shutoff valve on the water line that enters the back of the unit, typically located near the bottom where the water line connects. Turn this valve clockwise until it stops—this takes only a few turns. If you cannot locate this valve or it's stuck, you can proceed carefully and simply use your bucket to catch any water that drains. Turning off the water supply prevents unexpected leaks and makes the process safer.

Allow the system to depressurize by dispensing water into a cup until nothing comes out. This removes water pressure in the lines and reduces spillage during filter removal. Place your bucket underneath or near the filter location to catch any remaining water. Opening your freezer door and leaving it open during the process provides airflow and helps you see better if the filter is located in the lower portions of the refrigerator.

Many newer Whirlpool refrigerators include a filter reset button located near the filter housing or on the main control panel. Note where this button is located—you'll need to press it after installing your new filter to reset the filter status indicator light and restart the filter usage counter.

Practical Takeaway: Before you begin, locate the shutoff valve on your water line, find the filter location using your manual, and practice turning off the water supply valve to ensure you can do it smoothly when needed.

Removing the Old Filter and Stopping Water Leaks

With your bucket positioned to catch water and your water supply shut off, you're ready to remove the old filter. If your filter is housed in a cartridge with a cap, grip the cap firmly with both hands and turn it counterclockwise (lefty-loosey) using steady, even pressure. Most filters require about one to one-and-a-half full rotations before they release. If the filter is tight, wrap a dry towel around the cap for better grip, but avoid using tools that might crack the plastic housing.

As the filter loosens, water will begin dripping from the connection point. Continue turning slowly until the filter separates from the housing completely, then lower it into your bucket to catch any remaining water trapped inside. Expect about one to two cups of water to drain from the system—this is normal. Some water may also drip from the housing opening itself, so keep your bucket positioned underneath.

Once the old filter is fully removed, look inside the housing. You should see a small inlet tube or connection point. Inspect this area for any debris, mineral deposits, or rust. If you notice discoloration or buildup, dampen a clean cloth with water and gently wipe the inside surface and the inlet connection. This takes only a minute but significantly improves the performance and longevity of your new filter. Do not use cleaning chemicals or scrub aggressively, as this can damage the housing.

Some older Whirlpool models have a housing with a rubber seal or gasket at the connection point. Examine this seal on your old filter's connection end. If it looks cr

🥝

More guides on the way

Browse our full collection of free guides on topics that matter.

Browse All Guides →