🥝GuideKiwi
Free Guide

Free Guide to Replacing Your Whirlpool Dryer Heating Element

Understanding Whirlpool Dryer Heating Elements and When Replacement Becomes Necessary The heating element in your Whirlpool dryer is one of the most critical...

GuideKiwi Editorial Team·

Understanding Whirlpool Dryer Heating Elements and When Replacement Becomes Necessary

The heating element in your Whirlpool dryer is one of the most critical components in the entire appliance. This metal coil, typically made of nichrome wire wrapped around a ceramic or fiberglass core, generates the heat needed to dry your clothes. When electricity passes through the nichrome wire, it resists the flow and converts that electrical energy into thermal energy—the heat that warms the air inside your dryer drum.

Most Whirlpool dryer heating elements are designed to last between 3 to 7 years under normal household use, though this timeline can vary based on how frequently you run your dryer and how well you maintain it. The heating element works by cycling on and off throughout the drying cycle, controlled by a thermostat that monitors the temperature inside the drum. Each time the element cycles on and off, it experiences a small amount of thermal stress, which gradually wears down the material over time.

Several signs indicate that your heating element may be failing. The most obvious is when your dryer runs but produces little to no heat, leaving your clothes damp after a full cycle. You might notice that the first few minutes of the cycle produce some warmth, but then the dryer becomes completely cold. Another warning sign is a burning smell coming from your dryer, which suggests the element is beginning to break down electrically. Some people also report hearing unusual sounds, though this is less common with heating element failure specifically.

It's important to distinguish between a failed heating element and other potential problems. If your dryer isn't heating, the issue could also be a broken thermal fuse (a safety device that cuts power if the dryer overheats), a faulty thermostat, a disconnected heating element terminal, or a problem with your home's electrical supply to the dryer. This is why understanding the specific symptoms of heating element failure helps you diagnose the problem correctly before you begin any replacement work.

Practical Takeaway: Pay attention to how your dryer performs over time. A gradual decrease in drying power, clothes that feel damp after a full cycle, or a sudden complete loss of heat are all signs that your heating element may need replacement. Keep track of these symptoms so you can explain them to a technician if you decide to call a professional instead of replacing the element yourself.

Tools and Materials You'll Need for Heating Element Replacement

Before you begin any work on your Whirlpool dryer, gather all necessary tools and materials. Having everything on hand before you start prevents interruptions and makes the job move more smoothly. Most people can complete a heating element replacement with common household tools, though you may need to purchase a replacement element specific to your dryer model.

Essential tools include a screwdriver set with both Phillips and flathead options, a socket wrench set or adjustable wrench (the size depends on your specific model), needle-nose pliers for handling small components, and a multimeter to test electrical connections and verify the element has actually failed. A multimeter is a small electronic device that measures electrical voltage and resistance—you can find basic models at hardware stores for $15 to $30. You'll also want a flashlight or headlamp to see inside the dryer cabinet, since the heating element is typically located in a dark area beneath or behind the drum.

Safety equipment is non-negotiable. At minimum, wear work gloves to protect your hands from sharp metal edges inside the dryer cabinet. Safety glasses protect your eyes from debris. If you're concerned about electrical shock, an insulated screwdriver set adds extra protection, though the main safety precaution is unplugging your dryer before starting any work. Some people also keep a fire extinguisher nearby when working with heating elements, though this is primarily a precaution if something goes wrong.

The most important material you'll need is the replacement heating element itself. Whirlpool makes different heating elements for different dryer models, so you must identify your specific model number before purchasing a replacement. This information appears on a nameplate usually located on the back of your dryer or inside the door frame. Write down this model number and search for the exact replacement part—using the wrong heating element can damage your dryer or create a safety hazard. Replacement elements typically cost between $40 and $80, depending on your dryer model.

Additional supplies that make the job easier include a container or small bag for storing screws and fasteners as you remove them, a damp cloth for cleaning out lint and dust from inside the dryer cabinet, and possibly some high-temperature silicone sealant if your dryer uses it around the element housing. Having a repair manual or access to online resources specific to your model number is also valuable—these often include diagrams showing exactly where components are located and in what order they should be removed.

Practical Takeaway: Create a checklist of all tools and materials before you start. Organize your screws and small parts in a container as you remove them, labeling it with notes about which components they came from. Taking photos with your phone as you disassemble the dryer helps you remember how to reassemble everything correctly when you're done.

Step-by-Step Process for Safely Accessing Your Dryer's Heating Element

The first critical step is ensuring your dryer is completely disconnected from power. Unplug electric dryers from the wall outlet—don't just turn them off. For gas dryers with electric heating elements (some models), disconnect both the electrical outlet and turn off the gas supply valve if you're not completely confident about gas safety. This step cannot be skipped or rushed; electrical shock from a live dryer can cause serious injury or death.

Next, allow your dryer to cool for at least 2 to 3 hours if it was recently used. The heating element and surrounding metal components retain heat for a long time and can cause burns. You can safely proceed when you can comfortably hold your hand near the dryer's exterior without feeling residual heat radiating outward.

Different Whirlpool dryer models have slightly different designs, but the general process for accessing the heating element is similar. Most commonly, you'll need to remove the dryer's front panel or the access panel located at the bottom front of the unit. Consult your specific model's manual or search online for model-specific instructions, as the exact steps vary. Look for screws or fasteners holding the panel in place—these are usually clearly visible once you look closely at the edges of the panel.

As you remove screws, keep them organized by size and location. Taking a photo before you start removing anything helps you remember where each screw goes. Some panels have clips or latches in addition to screws, so look carefully around all edges. Gently pull the panel away from the dryer body—don't force it, as this can break clips or damage wiring. You may need to disconnect a door latch wire or other components before the panel comes completely free.

Once the front or access panel is removed, you'll see the dryer's internal components. The heating element is typically located inside a metal housing called the heater box or heating chamber, positioned below or behind the drum. You'll see the element as a metal coil or rod. Before touching anything, visually inspect the element for obvious damage—a completely broken element might show visible cracks or separations in the wire. You might also notice lint buildup around the heating chamber; gently clean this out with a dry cloth before proceeding.

Practical Takeaway: Document your disassembly process with photos taken from several angles. These photos are your reference guide for putting everything back together. Use your phone's voice recorder to narrate what you're doing as you work—this creates an audio record of the sequence, which some people find helpful when reassembling.

Removing the Old Heating Element and Testing for Failure

Once you've accessed the heating element, the next step is to disconnect the electrical terminals that supply power to it. The heating element typically has two metal terminals or connectors where wires attach. These terminals are usually held in place by push-on connectors that slide over the terminal posts. You can disconnect them by gently grasping the connector (not the wire) and pulling straight back. If the connectors are stuck, wiggle them gently while pulling—don't yank forcefully, as this can break the terminals off the heating element.

Before removing the element from its housing, test it with your multimeter to confirm it has actually failed. Set your multimeter to the resistance setting (usually marked with an ohm symbol

🥝

More guides on the way

Browse our full collection of free guides on topics that matter.

Browse All Guides →